RF Solutions

Audio Root - UHF SMA right angle whip antenna 450-900MHZ

450 – 900Mhz UHF ultra flexible right angle whip antenna with memory steel resistant to permanent bends . Cutting chart and colored end caps included.
Compatible with :

• AUDIO LIMITED DX2020
• AUDIO LIMITED DX2040
• AUDIO LIMITED DX2000
• AUDIO LIMITED Envoy En2 DX
• AUDIO LIMITED Envoy En2 DX2
• AUDIO LIMITED Envoy CXiR
• LECTROSONICS Sra
• MICRON SDR770
• WISYCOM MCR42
• ZAXCOM RX900
• ZAXCOM QRX100
• etc …

• AUDIO LIMITED TX2020
• AUDIO LIMITED TX2040
• AUDIO LIMITED TX2000
• AUDIO LIMITED miniTX
• AUDIO LIMITED DX2020
• AUDIO LIMITED DX2040
• AUDIO LIMITED DX2000
• AUDIO LIMITED Envoy En2 DX
• AUDIO LIMITED Envoy En2 DX2
• AUDIO LIMITED Envoy En2 TX
• AUDIO LIMITED Envoy En2 MX
• AUDIO LIMITED Envoy TX Blue
• AUDIO LIMITED Envoy CXiR
• LECTROSONICS SMV
• LECTROSONICS SMQV
• LECTROSONICS Sra
• MICRON TX700
• MICRON SDR770
• WISYCOM MCR42
• ZAXCOM RX900
• ZAXCOM QRX100
• etc …

• Frequency Range: 470 to 700 MHz
• Input Impedance: 50 Ω
• Output Impedance: 50 Ω
• Gain (each output): +6 dB to -10dB, user adjustable
• Current Consumption: 185mA

• Available Bandwidths:

• OIP3: > +41dBm
• Port to port isolation: > 20dB (min.)
• Noise figure: < 3 dB

• RF Inputs: 2 x 50 Ω Standard BNC Sockets
• RF/DC outputs to receivers: 2 x 4 x 50 Ω mini UHF SMA sockets
• Main ON/OFF Switch: Master switch
• DC Power OUT: 6 x 4-pin Hirose sockets individually fused and protected against reverse polarity, standard pin-outs, Pin1(-ve) and Pin4(+ve)

• External Power: 10-18V @ 1A (min.)*, reverse power and short circuit protected (*higher current limit is required if mixer/recorders are powered-max current 2A)
• Phantom dc to Receivers: 9Vdc (regulated), individually switched ON/OFF
• Remote Antenna Powering: Switchable dc T-bias powering, 12Vdc @ 200mA max, regulated for active antenna powering, short circuit protected
• Hirose dc output: Unregulated incoming volts, switched, individually fused and protected against reverse polarity

• Dimensions: 190x64x30mm (W x H x D)
• Weight: 0.4 kg
• Related accessories:

Shure ADX5BS-L

L-Type Battery Sled for Axient® Digital ADX5D

The ADX5BS-L is an L-type battery sled for use with the Axient® Digital ADX5D portable wireless receiver. Battery sleds for the Axient® Digital ADX5D must be used with the ADX5BP-TA3 backplate, as this backplate includes the 4-pin connector required for the two components to mate and pass power. With the ADX5BS-L, the ADX5D can be powered by one or two L-type batteries. When two batteries are installed, one can be replaced without interrupting operation. Battery runtime changes depending on the number, type, and capacity of the batteries used.

• Battery Sled for Axient Digital ADX5D dual-channel portable wireless receiver
• Compatible with L-type batteries
• Can power with one or two L-type batteries at a time, which allows for hot swapping of one battery while in use
• Battery Sled does not charge batteries (external charger is needed)
• Must be used with ADX5BP-TA3 backplate (purchased separately)

Shure ADX5D

Axient™ Digital Dual-Channel Portable Wireless Receiver

You make your living on a sound stage, in a sports arena, or wherever “on location” takes you. You depend on your wireless system to handle each and every situation with ease. Compatible with all AD series and ADX series transmitters, the Axient™ Digital ADX5D dual-channel wireless receiver delivers superior RF performance, spectral efficiency, and transparent audio quality in a portable, slot-in design. Sound and performance that the touring industry has adopted as industry standard is now available to audio professionals in film and broadcast. Wireless pinnacle. Now portable.

• Dual-channel slot-in form wireless receiver
• Impeccable audio quality
• Wide tuning range up to 184 MHz (region dependent)
• High spectral efficiency due to advanced digital modulation scheme offers more wireless channels in available RF space
• High Density (HD) mode provides even higher spectral efficiency (application dependent)
• True digital diversity reception per channel for drop-out resistance and excellent range
• Networked control with Wireless Workbench® software and ShurePlus™ Channels app
• 5-segment Channel Quality meters display per-channel RF link quality
• ADX series receiver with ShowLink Direct Mode allows remote control of Axient Digital transmitters without the need of external equipment*
• Third-party integration and control from select portable mixers and recorders for RF scan and deployment, audio gain adjustments, transmitter battery life monitoring, and more.*
• Party Dial feature enables users to quickly switch between RF channels from a pre-selected group of frequencies
• Optimized Menu Structure places the most commonly used features within a few clicks of each other
• Enhanced Shortcut Menu provides rapid access to only a few critical features and menus
• Aux 3.5mm audio output provide connection to headphones or to a balanced line-level input
• Accessory Mount with cold shoe adapter (sold separately)
• Removable antennas with standard SMA connectors
• High-resolution OLED display
• USB-C port for firmware upgrades
• Streamline user interface
• Low latency, down to 2 milliseconds